Flow Control Modules

Flow Control Module (Mod X1)

演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据,据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演,示数据演示数据演示数据演示数据演示数据演示数据演示数。据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据!演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据,据演

Voltage Range: DC 9~24V

Default parameters:
This product complies with MODBUS protocol instructions
Available command codes 0x03, 0x06, 0x10

Device default parameters:
Baud rate: 9600 (decimal)
MODBUS device address: 1 (decimal)
Flow meter constant K value: 50 (decimal)

This protocol follows the MODBUS protocol instructions

Register address Register function
0x0000 baud rate
0x0001 device address, can be modified to 0x0001-0x00FE (decimal 1-254)
0x0002 Sensor pulse K value, the value read and written is 10 times the actual value
0x0003 Permanent accumulated flow high register, unit, L
0x0004 Permanent cumulative flow low register, unit, L
0x0005 Permanent cumulative flow decimal, the reading is 100 times the actual value, unit, L
0x0006 Permanent cumulative flow pulse value
0x0007 Temporary accumulated flow high register, unit, L
0x0008 Temporary accumulated flow low register, unit, L
0x0009 Temporary cumulative flow decimal, the reading is 100 times the actual value, unit, L
0x000A Temporary cumulative flow pulse value
0x000B Real-time flow, unit: L/min, the reading is 100 times the actual value
0x000C output point 1, control solenoid valve 1, input 0x00FF, turn on, 0x0000, turn off
0x000D output point 2, control solenoid valve 2, input 0x00FF, turn on, 0x0000, turn off

The baud rate defaults to 9600 and the reading is 0. If you modify the baud rate, please modify the parameters as follows. (The parameters that can be modified are 0-3. If the data input is not a value between 0-1, the baud rate is 9600, but it will be displayed as the modified value is not 0 when reading)

Register parameters Baud rate
0 9600
1 4800
Baud rate parameter modification method:
1. The default baud rate is 9600, and the reading is 0.
2. If you modify the baud rate, modify the parameters as follows. (If you enter a value that is not in the table, the baud rate will be restored to 9600, but it will be displayed as the modified value is not 0 when it is read.)
Precautions:
1. After the address, baud rate, K value, and permanent cumulative flow are modified, the device needs to be restarted to take effect.
2. Please close the pipeline before clearing the accumulated flow to prevent water from passing through after the clearing. After 60 seconds, the value will change. If the program changes the value again, the accumulated flow cannot be reset to zero.
3. The temporary accumulated flow will be cleared after power failure, and the permanent accumulated flow will be recorded once every 60S. (The change in flow rate must exceed 1L within 60S to be recorded)

演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据,据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演,示数据演示数据演示数据演示数据演示数据演示数据演示数。

据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据!演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据,据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演,示数据演示数据演示数据演示数据演示数据演示数据演示数。据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据!

演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据,据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演示数据演,示数据演示数据演示数据演示数据演示数据演示数据演示数。

热门推荐

Home
Product
News
Contact